下载费用：180 文库币 &
SAE AS 08 (R)FITTING.UNION.BEAM SEAL. PSI.MALE ENDS
AEROSPACE STANDARD FITTING, UNION, BEAM SEAL,
PSI, MALE ENDS AS85421/11 SHEET 3 OF 3 REV. C 7. INTENDED USE: THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. CORROSION RESISTANCE STEEL AT 3000 psi. b. TITANIUM ALLOY AT 4000 psi. 8. DRY FILM LUBRICANT: APPLY DRY FILM LUBRICANT PER AS5272, TYPE I TO SEALING SURFACE. OVERSPRAY IN BORE IS NOT PERMITTED. 9. TITANIUM IS NOT RECOMMENDED FOR USE IN GASEOUS OR LIQUID OXYGEN SYSTEMS. 10. INTERPRETATION OF DRAWING PER ARP4296. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M； REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 uin Ra. FORGED SURFACES MAY BE 250 uin Ra. 12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS + .015, ANGULAR DIMENSIONS + 0° 30’ 15. EXAMPLE OF PART NUMBER: AS85421/11 V 06 SIZE CODE, TUBE SIZE IN SIXTEENTHS IN .0625 INCREMENTS MATERIAL CODE LETTER /1/ BASIC PART NUMBER 16. IN THE EVENT OF CONFLICT BETWEEN THE TEXT OF THIS DOCUMENT AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS DOCUMENT TAKES PRECEDENCE. NOTHING IN THIS DOCUMENT, HOWEVER, SUPERSEDES APPLICABLE LAWS AND REGULATIONS UNLESS A SPECIFIC EXEMPTION HAS BEEN OBTAINED. 17. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. AEROSPACE STANDARD FITTING, UNION, BEAM SEAL,
PSI, MALE ENDS AS85421/11 SHEET 2 OF 3 REV. C TABLE 1 - DIMENSIONAL DATA MASS,. LB/EA, APPROX, REF DASH NO. TUBE O.D. T THREAD AS8879 A B (REF) C (REF) ?E (MIN) TI CRES -03 .188 .3750-28UNJS-3A .637 .375 .156 .350 .010 .017 -04 .250 .4375-24UNJS-3A .727 .438 .162 .413 .015 .026 -05 .312 .5000-24UNJS-3A .739 .500 .174 .475 .019 .034 -06 .375 .5625-20UNJS-3A .793 .562 .188 .537 .023 .041 -08 .500 .7188-20UNJS-3A .873 .750 .242 .725 .045 .079 -10 .625 .8438-18UNJS-3A 1.051 .875 .292 .850 .067 .118 -12 .750 1.0000-16UNJ-3A 1.139 1.000 .300 .975 .080 .142 -14 .875 1.1250-16UNJ-3A 1.181 1.125 .306 1.100 .098 .173 -16 1.000 1.2500-14UNJS-3A 1.307 1.250 .372 1.225 .132 .234 -20 1.250 1.5781-14UNJS-3A 1.341 1.625 .412 1.600 .224 .397 -24 1.500 1.8438-14UNJS-3A 1.537 1.875 .438 1.850 .335 .593 NOTES: /1/ MATERIAL: a. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL PER AMS 5643. b. CODE LETTER T - TYPE 6AL-4V TITANIUM ALLOY BAR PER AMS 4928 OR AMS 4965. c. CODE LETTER V - TYPE 15-5PH, CORROSION RESISTANT STEEL PER AMS 5659. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER P - CONDITION H1075 PER AMS 2759/3. b. MATERIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - AGE TO CONDITION H 1075 PER AMS-H-6875 OR AMS . FINISH: a. MATERIAL CODE LETTER P - PASSIVATE PER AMS 2700, TYPE 6 OR 7 b. MATERIAL CODE LETTER T - NONE. c. MATERIAL CODE LETTER V - PASSIVATE PER AMS 2700, TYPE 6 OR 7. /4/ PROCUREMENT SPECIFICATION: AS85421 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS85421 FOR THIS STANDARD. SEE WW.EAUDITNET.COM FOR CURRENT QPL ON-LINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS578 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 AND SMALLER: MANUFACTURER’S NAME, CAGE CODE OR TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER, AND FORGING MANUFACTURER’S IDENTIFICATION WHEN MADE FROM FORGING. b. FOR SIZES 08 AND LARGER: MANUFACTURER’S NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER, AND FORGING MANUFACTURER’S IDENTIFICATION WHEN MADE FROM FORGING. 6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION. AEROSPACE STANDARD FITTING, UNION, BEAM SEAL,
PSI, MALE ENDS AS85421/11 Copyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerService@sae.org SAE WEB ADDRESS: http://www.sae.org ISSUED 2002-01REVISED 2008-01 THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3 REV. C FEDERAL SUPPLY CLASS4730 AS85421/11SHEET 1 OF 3 REV. C PROCUREMENT SPECIFICATION: AS85421 /4/SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences. Theuse of thisreportis entirely voluntary, andits applicabilityandsuitability forany particularuse,including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled.SAE invites yourwritten commentsandsuggestions.RATIONALE REVISED THE WEIGHT SPECIFICATIONS BASED ON SOLID MODELS OF EACH FITTING, QML/QPL NOTE AND UPDATED FINISH SPECIFICATIONS. FIGURE 1
文档加载中……请稍候！
下载文档到电脑，查找使用更方便
180 文库币 &&1人已下载
还剩页未读，继续阅读
<a href="UserManage/CopyrightAppeal.aspx?bid=1714072" title="版权申诉" class="fLeft works-manage-item works-manage-report" target="_blank"
关&键&词： SAE AS 11 十一 FITTING UNION BEAM SEAL PSI MALE ENDS
& 技术文库所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。
本文标题：SAE AS 08 (R)FITTING.UNION.BEAM SEAL. PSI.MALE ENDS 链接地址：
当前资源信息
编号： 12107
类型： 共享资源
格式： PDF
大小： 104.55KB
上传时间：
&& 盗版或侵权
&& 标题与内容不符合
&& 文档归类错误
&& 色情、淫秽、低俗信息
&& 反政府、反人类、反社会等反动信息
&& 散布赌博、暴力、凶杀、恐怖或者教唆犯罪等信息
&& 侮辱、诽谤等人身攻击信息
&& 散布谣言、扰乱社会秩序，破坏社会稳定等信息&#xe621; 上传我的文档
&#xe602; 下载
&#xe60c; 收藏
该文档贡献者很忙，什么也没留下。
&#xe602; 下载此文档
正在努力加载中...
下载积分：1000
内容提示：面试85421
文档格式：DOC|
浏览次数：0|
上传日期： 14:28:01|
文档星级：&#xe60b;&#xe60b;&#xe60b;&#xe60b;&#xe60b;
全文阅读已结束，如果下载本文需要使用
&#xe71b; 1000 积分
&#xe602;下载此文档
该用户还上传了这些文档
关注微信公众号