特斯拉做固态特斯拉线圈圈时怎么弄得高频交流电

后使用快捷导航没有帐号?
来自ValentinRuhry的创意,这哥们用整整500
自己做的火花间隙特斯拉线圈,人工高压闪电(SGTC)
本帖最后由 天下冥尊 于
12:41 编辑
这个特斯拉线圈搞了一个多月才搞出来,现在虽然出弧了,但是谐振还有待调谐
.jpg (82.72 KB, 下载次数: 57)
12:40 上传
这个是教程
(4.36 MB, 下载次数: 233)
12:52 上传
点击文件名下载附件
下载积分: 下载币 -5
注意:数值可能不准确,请慎重!
淘宝买的zvs驱动板,用摩托电瓶带动,
zvs套件及高压包和9个电磁炉电容0.33u的1.7x9个和运费和手续费(我没有银行卡,叫代购买的)总共68rmb
3m铜线和50cm直径5cmpvc管9rmb
去修家电的地方买拆机电容14个20rmb
3个锯片和50cm直径2cmpvc管2rmb
一条热熔胶1rmb
2两漆包线铜的10rmb
不锈钢球12cm& &8rmb
其他材料家里就地取材
IMG_250.jpg (29.51 KB, 下载次数: 58)
12:54 上传
IMG_209.jpg (43.29 KB, 下载次数: 65)
12:56 上传
IMG_323.jpg (43.02 KB, 下载次数: 63)
12:56 上传
IMG_658.jpg (49.58 KB, 下载次数: 62)
12:57 上传
电容组&&到后面总的数值是13nf& && && && &&&
IMG_315.jpg (43.57 KB, 下载次数: 65)
12:56 上传
IMG_109.jpg (42.92 KB, 下载次数: 54)
12:57 上传
我的次级是0.25mm漆包线在5cm的管子上绕34cm一千两百多圈吧
中间散了点&&还好我之前有用502& && && && && && && &&&
IMG_903.jpg (33.9 KB, 下载次数: 79)
12:57 上传
IMG_506.jpg (58.01 KB, 下载次数: 61)
12:54 上传
IMG_514.jpg (54.77 KB, 下载次数: 61)
12:54 上传
IMG_522.jpg (71.05 KB, 下载次数: 63)
12:55 上传
IMG_631.jpg (34.62 KB, 下载次数: 70)
12:55 上传
IMG_833.jpg (37.82 KB, 下载次数: 62)
12:55 上传
& &&&焊好的zvs拉弧
IMG_621.jpg (88.21 KB, 下载次数: 71)
12:55 上传
& && && &&&
IMG_715.jpg (69.73 KB, 下载次数: 69)
12:56 上传
IMG_243.jpg (83.43 KB, 下载次数: 53)
12:56 上传
制作次级和打火器
IMG_122.jpg (30.53 KB, 下载次数: 72)
12:57 上传
IMG_156.jpg (34.07 KB, 下载次数: 60)
12:57 上传
P{XC6K]Z`E~JDMDLKCT44@P.jpg (37.59 KB, 下载次数: 62)
12:57 上传
这是用单管自激驱动的电路图&&效率不高&&所以我用zvs
131644pgffhb1.jpg (41.08 KB, 下载次数: 65)
13:59 上传
不知道我的为什么不能从顶端球放电&&只能从连接顶端的电线放电&&有可能我顶端球有问题&&这个改天在看看吧
还有我的次级寄生电容加进去算谐振的话得出来的电容参数不谐振&&不知道怎么回事&&这个也等有空再弄吧
上第三次开机视频&&第一次和第二次根本不出弧(谐振没调好)不过现在的电弧很短&&还需调谐
很危险啊这个,看着都恐怖………………
请问车上的点火器是不是这个原理?
次级电流太弱 初级线圈有点少。
多多向楼主学习&&我也是学这个专业的
这个,在我11月份的计划里,楼主你线上,我随后就来,
什么意思?新手求赐教
gazelle 发表于
很危险啊这个,看着都恐怖………………
电流小,可以用手摸,高频交流电还有趋肤效应
hjxwqhty 发表于
什么意思?新手求赐教
百度&&特斯拉线圈
电弧短说明谐振没有调好。如果有信号发生器和示波器的话,就好调了。实在不行有信号发生器和万用表组和一下也可以。
Copyright &
Powered by积分2460&金币0 &铜板2458 &交易积分0 &技术积分2 &RMB0 &注册时间&
彩虹计划?恐怕离的太远。
积分1257&金币0 &铜板1257 &交易积分0 &技术积分0 &RMB0 &注册时间&
猛图来了 准备动工
(90.93 KB)
下载次数:3
(15.46 KB)
下载次数:1
[通过 QQ、MSN 分享给朋友]The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.The page is temporarily unavailable
nginx error!
The page you are looking for is temporarily unavailable.
Please try again later.
Website Administrator
Something has triggered an error on your
This is the default error page for
nginx that is distributed with
It is located
/usr/share/nginx/html/50x.html
You should customize this error page for your own
site or edit the error_page directive in
the nginx configuration file
/etc/nginx/nginx.conf.

我要回帖

更多关于 特斯拉线圈制作 的文章

 

随机推荐