浙江省缙云测温元件厂的影响因素有哪些

影响红外测温仪测量精度的因素有哪些?
影响红外测温仪测量精度的因素有哪些?
由于红外测温技术对工业等领域运用广泛,因此,对其测量精确度也提出了更高的要求。非接触红外人体测温仪在功能和技术上越来越完善,但是,也存在影响其精确度的因素,如果不多加留意,将会导致红外测温仪测量精度有所偏差,对此,小编结合仪商城资讯,整理了一些因素,如下:测量角度为了保证测量准确,仪器在测量时应尽量沿着被测物体表面的法线方向(垂直于被测目标表面)进行测量。如果不能保证在法线方向上,也应当在与法线方向成45°角内进行测量,否则仪器显示值会偏低。环境温度应严格按照仪器技术指标所标明的环境温度使用仪器,超过此范围仪器测量误差将会增大,甚至损坏。当环境温度较高时,可使用风冷、水冷装置或热保护套,热保护套可使仪器在高达200℃的环境下正常使用。手持式测温仪从一个环境拿到另一个环境温度相差较大的环境中使用时,将会导致仪器精度的暂时降低,为得到理想的测量结果,应将仪器在工作现场放置一段时间(建议最少30分钟)使仪器温度与环境温度达到平衡后再使用。空气质量烟雾、灰尘和空气中的其它污染物以及不清洁的透镜会使仪器不能接收到满足测量精度的足够红外能量,仪器的测量误差将增大。因此,最好经常保持透镜清洁,空气吹扫器有助于使透镜不受污染。电磁干扰仪器要尽可能远离潜在的电干扰源,如负荷变化大的电动设备。在线式仪器的输出和输入连接使用屏蔽线并确保屏蔽线良好接地。在强干扰环境下,使用外部保护导管,刚性导管比柔性导管好。不得将其它设备的交流电源引入同一导管内。环境辐射当被测目标周围有其它温度较高的物体、光源或太阳的辐射时,这些辐射会直接或间接的进入测量光路,造成测量误差。为了克服环境辐射的影响,首先要避免环境辐射直接进入光路,应该尽量使被测目标充满仪器视场,对于环境辐射的间接干扰,可采用遮挡的方法消除。视场与目标大小要确保目标进入仪器测量视场。目标越小,则应离得越近。在实际测量时,为了减小误差,最好能使目标的大小为视场光斑的两倍以上。因此,使用红外测温仪测量时,注意其测量角度、环境温度、电磁干扰等问题,便可获取精确度高的数据,同时也避免出现不必要的麻烦。
本文仅代表作者观点,不代表百度立场。系作者授权百家号发表,未经许可不得转载。
百家号 最近更新:
简介: 各类数码产品,新潮电子产品
作者最新文章测温元件的影响因素有哪些_百度知道
色情、暴力
我们会通过消息、邮箱等方式尽快将举报结果通知您。
测温元件的影响因素有哪些
热电阻插入被测场所时,沿着传感器的长度方向将产生热流。当环境温度低时就会有热损失。致使热电阻温度传感器与被测对象的温度不一致而产生测温误差,其插入深度应该深一些,陶瓷材料绝热性能好,可插入浅一些测温点的位置。总之,由热传导而引起的误差、代表性,如流动的液体或高速气流温度的测量,将不受上述限制,插入深度可以浅一些,具体数值应由实验确定。而插入深度又与保护管材质有关。金属保护管因其导热性能好。对于工程测温,其插入深度还与测量对象是静止或流动等状态有关,与插入深度有关,否则将失去测量与控制的意义,对于生产工艺过程而言,一定要具有典型性
为您推荐:
其他类似问题
您可能关注的内容
换一换
回答问题,赢新手礼包&&&测温元件
的翻译结果:
查询用时:1.495秒
&在分类学科中查询
The traditional transformer far biography measured the warm method is the transformer temperature element measured the warm signal changes delivering through the temperature, transforms for the linear DC voltage signal, again through the scene RTU special-purpose direct current simulation quantity Yuan biography module, passes on the transformer temperature by in the remote survey form.
传统的变压器远传测温方法是将变压器测温元件的测温信号通过温度变送器,转换为线性直流电压信号,再通过现场RTU专用的直流模拟量远传模块,将变压器温度以遥测量的形式上传。
From all measuring temperature system, thechoice of measuring temperature element, and the methods of the thermocoupleweld and its arrangement are introduced.
从整个测温系统入手,分别阐述了测温元件的选择、热电偶的焊接及敷设等方法;
The formula and method has an important direction for the design of temperature sensors that is using thermal resistant as measure temperature element.
对以热敏电阻作为测温元件的温度传感器的设计具有参考意义.
A measuring device for melting and crystallization parameters of slag has been developed using single thermal couple which not only is as a measuring temperature element, but also as a heating element with the characteristics of higher speed of temperature going up and lowering and higher measuring efficiency.
研制了热丝法炉渣熔化和结晶参数测定仪,该测定仪用一根双铂铑热电偶丝既作加热元件又作测温元件,具有升、降温速度快,测量效率高的特点。
Heat-conduct analysis of measuring error of thermometric component
测温元件测量误差的传热学分析
The system adopts J
type electric thermocouple as thermometric component and realizes effective compensation of the temperature at the cold
end of thermocouple by using temperature sensor AD590 of integrated circuit. Thus it can be improved in accuracy and stability and noise proof performance.
它采用J类热电偶作为测温元件 ,利用集成电流的温度传感器AD5 90 ,实现热电偶冷端温度的有效补偿 ,从而提高系统的精度、稳定性和抗干扰性能 .
A thermo-electrochemical equation for half-cell reaction was derived as Thermo-electrochemical measurement, using thermoelectric coupling as the thermometric component, was adopted. Absolute entropy change of Fe(CN)63-/Fe(CN)64- electrode was determined as 146.5 J·mol-1·K-1 at 298.15K with the equations derived.
提出电化学半反应的热电化学公式采用以热电偶为测温元件的热电化学测试系统对测试体系进行研究,利用提出的公式计算出铁氰化钾体系电极反应在298.15K的绝对熵变为146.5J·mol-1·K-1。
Based on an analysis of the reguirments of temperature on roller face in coating film process, the authors advance a calculating method of electricheating tube power which roller reguired base on thermal eguilibrium principle, introduce a non-contact thermometric element and roller temperature control system and its operating result.
分析了复膜工艺对辊筒表面温度的要求,提出基于热平衡原理的辊筒所需电热管功率的计算方法.介绍了一种非接触式测温元件和辊筒温度控制系统及其运行结果
Thermal resistor, a kind of thermometric element, is extensive used in the field of astronautics. Because of bad concordance, the corresponding relationship between the resistor and temperature must be calculated when the element is used.
热敏电阻是一种在航天领域广泛应用的测温元件 ,由于其一致性差 ,使用时必须给出每个元件的电阻—温度对应关系。
The DS1820 with accuracy as high as 0.5℃ is a l-wire digital semiconductor thermometer component produced by DALLAS semiconductor corporation of America.
DS1820是美国DALLAS公司生产的单线数字化半导体测温元件,测温分辨率为0.5℃。
The DS1820 is a 1-wire digital thermometer produced by Dallas semiconductor corporation of America. Measures temperatures range from -55℃ to +125℃ in 0.5℃ increments.
DS1820是美国DALLAS公司生产的单线数字化半导体测温元件,其测温范围为-55~+125℃,测温精度0.5℃。
A Rhodium-Iron resistance is chosen as the sensor whose resistance R0 is 50Ω. The temperature can be controlled stablly±0.01K within the setpoint and measured and displayed as accuratelly as 0.01K.
使用R_0≈50欧姆铑铁电阻作测温元件,可将温度控制在±0.01K并能同时显示温度,分辨率为0.01K。
Design of temperature controllor uses digital temperature sensor DS18B20 and AT89S52 singlechip. Output controller adopts light coupling MOC3061 single aspect adjust power circuit,straightly to control or to heat water tank temperature. The interface of man and engine adopts HD7279A keyboard displaying circuit.
温度控制器采用数字温度传感器DS18B20为测温元件,以AT89S52单片机为控制核心,通过光耦合MOC3061单向调功电路作为输出部分,直接对水箱温度进行加热控制,人机接口采用HD7279A通用键盘显示电路。
Introduces a new kind of temperature measurement distributed system based on LonWorks field bus technology. Its temperature measurement apparatus adopts DS18B20 which is a new single bus digital temperature sensor.
以LonWorks现场总线技术为基础,以新型单总线数字温度传感器DS18B20为测温元件,提出了一套新型的分布式测温系统。
查询“测温元件”译词为用户自定义的双语例句&&&&我想查看译文中含有:的双语例句
为了更好的帮助您理解掌握查询词或其译词在地道英语中的实际用法,我们为您准备了出自英文原文的大量英语例句,供您参考。&&
在英文学术搜索中查有关的内容
在知识搜索中查有关的内容
在数字搜索中查有关的内容
在概念知识元中查有关的内容
在学术趋势中查有关的内容
2008 CNKI-中国知网
北京市公安局海淀分局 备案号:110 1081725
&2008中国知网(cnki)
中国学术期刊(光盘版)电子杂志社影响红外测温仪温度测量的主要因素有哪些_百度知道
色情、暴力
我们会通过消息、邮箱等方式尽快将举报结果通知您。
影响红外测温仪温度测量的主要因素有哪些
我有更好的答案
是否在允许范围内;(2).是否正确瞄准(3).选择的光谱范围(波长)是否合适,对于测量有玻璃窗口的容器内目标时.有无窗口玻璃,窗口玻璃对红外能量有衰减,因此会使单色测温值偏低(可通过调整发射率值来修正);(5)、氧化、喷砂),几何形状(平面、凹面影响红外测温仪温度测量的主要因素;(6).发射率是否设置正确:被测物质本身因素:(1)物质的材料(2)表面特性;表面质量(光亮、粗糙.烟雾、水蒸气、灰尘,光谱范围不能选择8~14μm,而应选择1μm附近的、凸面)测温仪测温现场因素:(1).测量角度;而对比色测温值基本没有影响;(4)
采纳率:50%
来自团队:
为您推荐:
其他类似问题
您可能关注的内容
换一换
回答问题,赢新手礼包

我要回帖

更多关于 电机测温元件 的文章

 

随机推荐